Metallic Epoxy Flooring
Unique, high-gloss finishes that turn a garage or living space floor into a visual feature - no two metallic epoxy floors look the same.
Learn MoreLoading...
Serving San Angelo, TX and surrounding areas. (325) 292-0567
Faster curing than epoxy, better heat resistance, and a finish that holds up through West Texas summers - your garage is back in use within 24 hours.
Polyaspartic floor coatings in San Angelo bond directly to concrete and harden into a tough, glossy protective layer - most garage jobs are completed in a single day and the floor is ready for your vehicle within 24 hours.
Standard epoxy is a proven product, but it has two real weaknesses in West Texas: it cures slowly and it can soften or peel under the kind of heat San Angelo garages see from May through September. Polyaspartic coatings cure in hours rather than days and are formulated to hold their bond and appearance in extreme heat. If you are still weighing your options, our garage floor coatings page walks through both systems side by side so you can make an informed choice.
A properly installed polyaspartic coating on a well-prepared floor typically lasts 15 to 20 years. The key word is "prepared." Grinding, crack repair, and proper priming determine whether the coating bonds for two decades or peels in two summers - and that prep work is where we invest the most time.
San Angelo sits on heavy clay soil that swells when it rains and shrinks when it dries. That movement is what starts the cracks you see in your slab. A coating applied over properly repaired cracks stops the damage from spreading and gives the floor a protected, clean surface.
If scrubbing your garage floor still leaves dark stains from oil drips or hot tire marks, the concrete has absorbed those materials into its surface. A polyaspartic coating seals the slab so future spills sit on top and wipe clean instead of soaking in.
Older concrete floors in San Angelo homes - especially those built in the 1970s and 1980s - often produce a fine gray powder even after sweeping. This is the surface slowly breaking down. A coating stops the dusting entirely and gives you a hard, sealed surface.
If you are turning your garage into a workshop, home gym, or finished storage area, bare concrete is not the right surface. A coated floor is easier to clean, easier on your feet, and looks finished - which matters when the space becomes part of your daily routine.
Our polyaspartic system includes full mechanical surface preparation, crack filling, base coat, decorative chip broadcast, and a clear topcoat - all completed in a single day in most cases. Decorative chip blends are available in dozens of color combinations, and we bring physical samples to your estimate so you can see what the finished floor will actually look like before committing. If you prefer the look of a solid metallic or high-gloss finish, our metallic epoxy flooring service offers striking, one-of-a-kind results for garages and living spaces.
We also offer polyaspartic coatings for commercial and light-industrial spaces where a fast turnaround is critical. If your business cannot afford several days of floor downtime, polyaspartic is almost always the right call. Every job comes with a written estimate that breaks out prep, materials, and finish - so you know exactly what you are paying for before anyone touches your floor.
Suits homeowners who want a durable, fast-curing finish that holds up through West Texas summers and gets them back in the garage the next day.
Suits anyone who wants a finished, showroom look with color choices and a small amount of built-in slip resistance.
Suits businesses and shops that need minimal downtime - polyaspartic cures fast enough to reopen a floor within hours of the final coat.
Included with every job - mechanical grinding, crack filling, mineral stain treatment, and priming before any coating is applied.
San Angelo summers push past 100 degrees for weeks at a stretch, and garage floors that bake in the heat all day are a serious challenge for standard coating systems. Polyaspartic coatings handle this better than epoxy - they resist heat distortion, do not yellow or soften under UV exposure, and resist the hot tire damage that peels standard epoxy right off a West Texas garage floor. We also schedule application during cooler morning hours during summer months, which helps the material cure evenly and bond as strongly as possible. San Angelo's dry, semi-arid air actually helps here - low humidity means faster, more reliable cure times than you would see in a more humid part of Texas.
The clay soil across Tom Green County is the other factor that shapes how we approach every job. Homeowners in Miles and Carlsbad - like most of the region - sit on soil that shifts with every wet-dry cycle, and that movement is exactly what causes the cracks in older slabs. We inspect every floor carefully, identify active versus stable cracks, and fill them as part of our standard prep process. We also look for and treat the mineral staining that San Angelo's high-mineral water often leaves on concrete near drains and low spots.
We respond within 1 business day. We ask about your garage size, any cracks or previous coatings, and what you are hoping to accomplish. No estimate is given before we see the floor - the condition of the slab changes what the job involves.
We walk your floor, check for cracks, test for moisture, look for mineral staining, and measure the space. You leave with a clear written quote that covers surface preparation, the coating system, and finish options. No surprises later.
Move everything off the slab before installation day - cars, shelving, bikes, storage boxes, everything. Full floor access is required. Your contractor will remind you of this when confirming the appointment.
The crew grinds the floor, fills cracks, applies the base coat and chips, then seals with the topcoat - all in one day for most garages. We walk you through the finished floor and explain care instructions before we leave. Your car goes back in within 24 hours.
Free written estimate. No obligation. Your car goes back in the garage within 24 hours of completion.
(325) 292-0567We select polyaspartic formulas that are rated for high-temperature performance and schedule summer applications during cooler morning hours. That combination ensures the coating cures evenly and bonds as strongly as possible, even when your garage has been baking since June.
Every floor we coat is mechanically ground before any product is applied. Grinding opens up the concrete surface so the coating bonds at the structural level - without it, even the best polyaspartic product will eventually separate. The American Concrete Institute identifies surface preparation as the most critical factor in coating longevity.
We fill and stabilize cracks as a standard part of our prep process - not an add-on charge. San Angelo's clay soil will keep moving, but properly filled cracks that have been stable will not reopen through the coating. We address them before anything else.
We visit your floor before we quote. The condition of your slab - how much cracking, staining, or mineral buildup is present - directly affects what the job involves and what it costs. A phone quote without seeing the floor is a guess, not a commitment. Ours are based on reality.
A polyaspartic coating installed correctly lasts 15 to 20 years. Installed incorrectly - over an unground, unrepaired slab - it fails in one or two. We focus on the preparation that makes the difference. American Concrete Institute guidance on concrete surface preparation is a useful resource if you want to understand what quality prep looks like before you call any contractor.
Unique, high-gloss finishes that turn a garage or living space floor into a visual feature - no two metallic epoxy floors look the same.
Learn MoreSide-by-side comparison of epoxy and polyaspartic systems to help you choose the right coating for your garage and budget.
Learn MoreCall today or submit a request - we respond within 1 business day and your car goes back in the garage within 24 hours of installation.